-13%

3D Printer Kit MKS Gen V1.4 Control Board MEGA2560 Motherboard + RAMPS 1.4 With USB Cable+ 2004 LCD+ 5PCS A4988 Stepper Motor

52,49 45,67

Comparer
SKU: 32808966503 Category:

Description

3D Printer Kit MKS Gen V1.4 Control Board MEGA2560 Motherboard + RAMPS 1.4 With USB Cable+ 2004 LCD+ 5PCS A4988 Stepper Motor

Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4,

an effective solution to the hot bed MOS pipe heat problems. The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.Can be directly connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel. Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit. Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs. 2004 LCD Controller Board: his Smart Controller contains a SD-Card reader, an rotary encoder and a 20 Character x 4 Line LCD display. You can easy connect it to your Sanguinololu board using the “smart adapter” included. After connecting this panel to your Sanguinololu you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card. A4988 stepper driver: A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product. Low RDS (On) Output Automatic current decay mode detection / selection Mix with slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic supply Thermal shutdown circuitry Ground fault protection Load short-circuit protection Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Package Contents: 1x MKS Gen V1.4 3D Printer Controller Board Whit USB 1x 2004 LCD Controller Board 5x A4988 stepper driver

  • We accept Credit Card, Escow, Western Union, TT. You can choose a method which is the most convenient for you.
  • Payment must be made within 7 days of order. If you can’t check out immediately after auction close, please wait for a few minutes and retry.
  • To protect your interests, your payment will be temporarily held by Aliexpress, and will not be released until you receive your order and are satisfied with it.

Shipping Method

Shipping Cost

Tracking Number

Shipping Time

ePacket

Free

Yes

7-20 days

China Post Air mail

Free

Yes

20-60 days

HongKong Post Air mail

Free

Yes

15-45 days

EMS

Check the site

Yes

5-10 days

DHL

Check the site

Yes

3-8 days

UPS

Check the site

Yes

3-8 days

Fedex

Check the site

Yes

3-8 days

  • We Ship to Worldwide, except APO/FPO.
  • Items are shipped from China using Airmail, reach most of the countries within 10 to 20 business days.
  • Delivery time depends on destination and other factors.
  • If you purchase more items and need some discount of the shipping fee, please send the message to us, and we’ll respond you in 1 business day.
  • Accept DROP SHIPPING. Please confirm the address. We only ship to cinfired order address, and your order address mus MATCH your shipping address.
  • We highly value long term business relations. Buy with confidence!
  • If you are not satisfied when you receive your item, please return it within 14 days for a replacement or money back. Please contact me before you return it.
  • If item is defective in 3 months, we will send you a replacement without extra charger, or offer refund after we receive the defective item.
  • If item is defective after 3 months, you can still send it back to us. We will send you a new one after receiving the defective item. But you have to pay the extra shipping fee.
  • We depend on our customer satisfaction to succeed. Therefore, your feedback is extremely important to us.
  • If you are satisfied with our items, please leave a positive feedback to us. We will leave a positive feedback to you later.

Contact us by e-mail or our trade manager, before leaving any negative or neutral feedback or open any dispute. We’ll deal with you to solve any problems as soon as possible.
Wish you have a great shopping experience here!

Additional information

Brand Name

OSOYOO

Model Number

ZZDBGD1400

Ships From

China